Spot / Stain Removal Melbourne
When it comes to stain removal the number one influencing factor for a successful stain removal is, treating the stain as soon as possible. We can remove most spots or stains tackled correctly. Regardless of the cause, the success rate is much higher when a spot is still fresh.
Grime Fighters technicians are stain removal specialists, with our high attention to detail and premium quality products we are able to remove many of the most challenging stains. If anyone can successfully remove your stain we can. It is even possible to repair permanent stains with one of our carpet repair procedures such as, redyeing or cutting out the stained area and replacing it.
Normal spot and stain removal is a part of our cleaning process. Stains remaining after the cleaning process require specialised treatments. Any such treatments, like heat transfer or spot dyeing, can be discussed and quoted immediately after cleaning.
Given spills don’t always occur at convenient times when you can easily call the first available carpet cleaner. Its times like this when a little bit of knowledge goes a long way.
Never use store bought spot & stain removers. More often than not these products are too harsh for many carpets and as a result can remove colour from the carpet, leave a sticky residue behind or set the stain making removal at a later stage impossible even by the most experienced stain removal technicians.
The perfect stain removal kit made from common household items
- White or old colourfast cotton towels/nappies or rolls of absorbent paper towel
- Clear hand dish washing liquid (e.g. Dawn)
- White vinegar
- Carbonated or soda water
- Empty spray bottles
- White cotton cloths
- Absorbent sponges
Stains Removal - Coke Stains
Simple procedures to safely remove most stains
By following a few simple procedures you should be able to safely treat most stains without causing irreversible damage.
If the spill is fresh, blot up as much as possible with a white or colourfast cotton towel, or wad of absorbent paper towel. If spill contains solids use a spoon or dull knife to remove any solids by scraping from outside edge towards the centre and scoop it up. This avoids spreading the stain.
If dry, spray or apply with a sponge a small amount of cold water or carbonated water over the spill and work it in with the spoon to attempt to re-liquefy then start the blotting process. For dried solids use a spoon and vacuum cleaner to remove as much as possible before adding moisture.
Use a fresh part of the towel or fresh wad of paper towel and apply pressure or stand on it to blot. Repeat this procedure until no more residue from the spill transfers to the towel.
- Mix a solution of ¼ teaspoon of clear hand dish washing detergent with 1 cup of warm (not hot) water and stir gently.
- Apply detergent solution directly to a white cloth. Dampen the carpet fibres of the stained area with the cloth. Avoid saturating the carpet.
- Wipe or dab lightly, turning the cloth frequently. If necessary, use your fingertips to work the solution into the base of the stain. Never rub, scrub or use a brush. This may permanently damage fibres.
- Wet the stained area with clear lukewarm water to rinse. A spray bottle works well for this step. Avoid over wetting.
- Use a fresh area of your to towel or fresh wad of paper towels and apply pressure or stand on them to blot.
- Repeat the rinsing and blotting procedures until you are sure all traces of the detergent solution have been removed.
If treating urine stains, follow with Step 2
- If the stain is gone place a fresh absorbent towel or 1 centimeter thick wad of paper towel over the cleaned area and weigh it down with a heavy colourfast object such as a pile of magazines in a plastic bag.
- Replace towels for fresh ones regularly until the carpet dries
If the stain remains you can find additional spotting procedures in our stain removal guide or if you would prefer to get it done by the professionals you should have at least made the spill safe enough that it can wait until you can get someone out to remove what’s left of the stain without effecting chance of successful removal.
Step 2: Urine Stains
- Mix 1 cup of white vinegar with 2 cups of water
- Apply vinegar solution, rinse and blot as outlined above